|
|
|
|
|
|
|
Garden games table
|
 |
|
This games table is tough enough to stay outdoors all year long
|
|
|
By John Sillaots, photos by Christopher Campbell, illustration by Len Churchill
|
|
|
|
|
To adhere the tiles to the baseboard, use a latex-modified thinset mortar. I used a product called Super Flex manufactured by TEC Specialty Products Inc. Spread the thinset mortar onto the baseboard using an 1/8" notched trowel. Cover as much area as you can comfortably tile in five minutes. The angle of the notched trowel from vertical determines the height of the mortar ridges. What you're after is enough mortar to cover the bottom of the tile when pushed into place. Too much and it will squish up into the space between the tiles--too little, and your tiles won't be held securely to the plywood.
Let the tiles set for 24 hours before cutting the baseboard to size. Use a tablesaw, with the blade lowered so it doesn't quite make it through the top of the plywood. This prevents the blade from being damaged by the tile or mortar. Use a sharp utility knife to complete the cut through the baseboard.
Next, centre the tile-covered baseboard on the project top and fasten it with glue. Make sure any glue squeeze-out is removed when doing this--hardened blobs of glue will interfere with the installation of the top trim members. Gluing large flat parts together like this can be tricky because they slide around. You can eliminate this problem by hammering three or four 1" finishing nails part way into the project top, then nip off the nails with wire cutters so only a tiny tip of metal remains above the surface. This trick prevents movement of the tile base board completely. Place a heavy weight on top of these parts before setting them aside to dry. After 15 minutes, check the edges again for squeeze-out and remove any while it's still soft.
Top Trim
The area around the tiles is capped by top trim members and trim strips. After ripping a standard 1 x 6 to width for the top trim members, use the leftover wood for the trim strips. Glue these to the underside of the top trim, on edge, then mitre the ends of the assemblies after they're dry. For my project all four sides were mitred to a length of 25". This created a 1/8" grout space between wood and outer tiles, though exact sizes will be slightly different on your project. After gluing the trim parts in place, I sanded the top surfaces at a slight angle to shed the rain.
Before grouting between the tiles, apply finish to the exposed wood. I used three coats of Helmsman Spar Urethane on the top, and a flat black exterior latex on the plywood. When the finish has dried, grout the tiles using more thinset mortar. Apply a generous amount of mortar to the surface of the checkerboard and force it into the joints with a rubber-faced float. Make sure that the joints are completely filled so that there are no air bubbles or gaps. Remove the excess mortar by pulling diagonally across the tiles with the float. Rinse a sponge in clean water and wipe away any remaining mortar. Continue to rinse out the sponge and wipe away mortar until the joints are smooth and level with the tiles. After about 30 minutes a hazy film will appear on the surface of the tiles. Wipe this off using a soft cloth.
Installation
A 12" dia. lazy Susan bearing allows the table to be rotated so it can be adjusted to take full advantage of the sun. The bearing is sandwiched between two discs of 3/4" plywood. Lay out these discs with a compass and cut them out with a hand-held jigsaw. The bearing is attached to the plywood discs with 3/4" screws. Attach the bearing to one disc first, then drill oversize access holes to reach the screws to attach the other side. For my installation I used a 31/2"dia. steel post and attached the bearing assembly to the post with metal L-brackets. Another option would be to use a cedar 4 x 4 post set into a concrete footing to support the table. If you choose the 4 x 4 approach, make wooden support brackets using the template from the plan and secure them with biscuits and polyurethane glue. This treatment results in a more decorative look.
The final step is to add the game pieces. You could use traditional game pieces, but a local craft supply store provided something more appropriate for the garden--tiny wooden birdhouses. Paint the birdhouses to coordinate with your tiles and even between games, your outdoor games table will look great.
|
|
|
|
|
|
|
|
|
